Topic: Light Saber (Read 7079 times)

intermech · « **on:** September 11, 2010, 05:05:22 pm »

I had been watching some how-to's on YouTube about making a replica light saber from plumbing supplies. Unfortunately, Lowes did't have all of the parts I needed to build what I wanted. So I went the cheaper way and just bought some silver spray paint and made one out of an old toilet float valve I had and some old windshield wiper blades.

Here are the results (the last one is they type of toilet valve I used:

Starfox1701 · « **Reply #1 on:** October 05, 2010, 10:24:35 pm »

Ah another Jedi builds his first Lightsaber. Impressivel; your skills are complete.

Kreeargh · « **Reply #2 on:** October 05, 2010, 10:57:46 pm »

Beautifull work there

. How does it feel in the hand?

intermech · « **Reply #3 on:** October 06, 2010, 08:43:55 am »

Obe Wan has taught me well.

I was a little bit worried about the high profile of the windshield wiper blades, but as it turns out, they role one way or the other in your palm and take the stress off of the glue. I was concerned that the stress of wielding the hilt would pull the blades off, but the contact area sees virtually no stress. It does not feel too bad. It would be better if the pressure was spread more evenly across the hand. My next iteration will have stacked O-rings.

Tulwar · « **Reply #4 on:** November 04, 2010, 01:14:55 am »

The old photographic flash units that were used as the origional props are very collectable.

Kreeargh · « **Reply #5 on:** November 04, 2010, 10:06:15 pm »

Quote from: Interstellar Machine on October 06, 2010, 08:43:55 am

Obe Wan has taught me well.

I was a little bit worried about the high profile of the windshield wiper blades, but as it turns out, they role one way or the other in your palm and take the stress off of the glue. I was concerned that the stress of wielding the hilt would pull the blades off, but the contact area sees virtually no stress. It does not feel too bad. It would be better if the pressure was spread more evenly across the hand. My next iteration will have stacked O-rings.

get some paintable calk and fill in between the blades thicken it up some with layers not 1 try. It should make the blades stronger and have a better hand on feel to it. + if you wait to the right time after applying the last layer wet your hand with water then hold it for 15 seconds it should mold the thing to your hand and have a "percect fit" in theory anyway

O rings in my oinion dont work they wont fit the hand to grip the weapon well enough to controll.

intermech · « **Reply #6 on:** February 23, 2011, 01:24:47 pm »

This is my newest light saber. I spent quite a bit of money on the chromed pieces, but I am pretty happy with it. I have in mind how to make a cheaper one using aluminum foil tape.

intermech · « **Reply #7 on:** March 10, 2011, 07:40:57 am »

Here are a few more . . .

Roychipoqua_Mace · « **Reply #8 on:** March 10, 2011, 07:57:29 pm »

Quote from: Interstellar Machine on February 23, 2011, 01:24:47 pm

This is my newest light saber. I spent quite a bit of money on the chromed pieces, but I am pretty happy with it. I have in mind how to make a cheaper one using aluminum foil tape.

These are awesome! I like this first new one better than most of the movie ones even.

intermech · « **Reply #9 on:** August 22, 2011, 03:42:54 pm »

Here is another one, this one is a good on the shelf or hang from your belt prop, it is light but you cannot add a blade 'cause I sealed it off:

Starfox1701 · « **Reply #10 on:** August 22, 2011, 04:31:17 pm »

nice ; ever consider becoming a pro saber smith?

News: